Product: Download Pattern Construction Children: Baby Clothes
Download Pattern Construction Children: Baby Clothes
In this E-Dossier you will find instructions for the pattern construction of baby clothes

Taking Measurements

This picture shows the measurement of body you need for a pattern construction.

Types of Measurements

  • Made-to-measure: Personal body measurements and calculated measurements. As a foundation for the design pattern, the basic block (or basic pattern) is drafted using personal body measurements. Nevertheless, patternmakers and tailors work increasingly with basic patterns based on standard measurements and standard sizes to improve efficiency. Often, the basic block can be altered within a short period.
  • Industrial sizing code: Standard measurements from a size chart. Size charts reflect average measurements and are based on measurement surveys. The data of 1000 girls and women between 2 to 70 years of age was collected to produce the sizing system. These surveys are revised and updated every 10 — 11 years by the German Federation for Women’s Wear. Since average body measurements and figure proportions are constantly changing, the value of a size chart is temporarily limited.

Measuring

General information:

To determine the body measurements, the person being measured should be dressed only in underwear, so that the tape measure lies flat around the body. The measuring should not take place in front of a mirror as the client is apt to correct their posture resulting in imprecise measurements.

Tools required for taking measurements:

Height measuring device or wall chart, waist tape measure (measuring tape with hook and eye for marking the natural waist and for measuring the back and front length), ordinary measuring tape, small tailor’s square, cardboard strip, approx. 50 cm long pencil, eraser and measurement chart.

Additional information for the measurement chart:

Besides the body measurement, additional remarks about the figure proportions such as round back, sloping shoulder etc. are helpful. It is advisable to calculate certain auxiliary measurements and to compare the results with the measured ones in order to acquire data about the client’s figure type (proportion variations) for the pattern construction. If differences occur, the measurements should be double checked in order to exclude measuring errors (see measurement chart and calculation chart).

Measurement comparison:

In the standard size chart for women, the body measurements are always in direct relation (proportion) to each other. If the body measurements are out of proportion, it is an indication for a possible figure problem, such as full or small bust, waist, hips as well as strong or flat seat.

Comparison of the measured and the calculated measurements:

The calculated measurements derive from the primary body measurements BH (body height) and CG (chest girth). A comparison of the calculated and measured results should be conducted

for the following measurements: FWL 11 (front waist length 11) and BWL (back waist length). Minor differences can be taken into account during the normal pattern construction. Greater deviations however indicate possible figure problems such as “round back” or „full bust with upright figure”. These require further adjustments.

 

Taking Measurements

Primary Measurements

BH — Body height

This figure shows the measurement of the Body Height

 

  • Measure the height from the top of the head to the floor (Without shoes). The body height can be measured exactly if the client stands in front of a wall measuring strip. Mark the highest point of the head with a square.

 

 CG—Chest girth

This figure shows the measurement of the Chest girth

  • Measure the circumference over the fullest part of the bust (bust points) and across the lower part of the shoulder blades, With the measuring tape slightly lifted at the back. Take the measurement from the back of the client.

Ubg – Under bust girth

Diese Zeichnung zeigt das Messen des Unterbrustumfangs.

  • Measure the chest circumference horizontally just below the bust.

WG —Waist girth

This figure shows the measurement of the Waist girth

  • Measure the circumference at the narrowest part of the waist. Place the measuring tape horizontally around the waist. Take the measurement from the front of the client.

 

Lwg – Low waist girth

This figure shows the measurement of the Low waist girth

 

  • Measure the horizontal circumference 8 cm below the waist.

HG — Hip girth

This figure shows the measurement of the Hip girth

  • Measure the circumference over the strongest part of the seat and / or the hip. Take the measurement from the front of the client. Note any obvious figure proportions: e.g. one-sided high or strong hip, full or flat seat, and full or flat abdomen.

 

SL — Sleeve length

This figure shows the measurement of the Sleeve length

  •  Measure the sleeve length over the bended elbow from the shoulder tip to the wrist bone. This length can be measured at the sleeve from the sleeve cap to the hem. Add the shoulder Width to the sleeve length to determine the Kimono sleeve length.

 

Secondary Measurements

  • Mark the waistline with a waist tape measure With hook and eye closure. Check the correct horizontal position of the waist tape measure and note any obvious figure deviations. The correct position is important since the balance measurement of the front waist length and the back waist length are measured to the waist.

 

SD — Scye depth

This figure shows the measurement of the Scye depth

  • Measure the scye depth from the vertebra (base of the neck) to the armhole depth. Place a cardboard strip (approx. 50 cm long) under the arm. Fold the cardboard strip horizontally to the centre back. Measure the scye depth at the centre back from the base of the neck to upper edge of the strip. Since measuring the scye depth accurately is very difficult, the measurement should be compared With the calculated scye depth. Use the calculated measurement if the difference is up to 1 cm; for a  difference of more than 1 cm use the average value between the calculated and the measured scye depth.

 

BWL — Back waist length

This figure shows the measurement of the Back waist length

  • Measure the back waist length from the vertebra (base of the neck) to the lower edge of the waist tape measure. Place the waist tape measure (measuring tape With hook and eye) at the narrowest part of the waist. – Required for measuring the back and front waist length! To determine the position of the base of the neck, put a measuring tape around the neck and measure from the lower edge of tape  downward.

 

HD—Hip depth

This figure shows the measurement of the Hip depth

 

  • Measure the hip depth from the vertebra (base of the neck) to fullest part of the hip. This measurement is  only necessary for strong hips or thighs. Use the calculated hip depth for normal figure types.

 

 

Kl – Knee length

This figure shows the measurement of the Knee length

  • Measure the finished length from the vertebra (base of the neck) to the desired length.

 

BL I I— Bust Length I + II  –  Bt I + II

This figure shows the measurement of the Bust length

  • Measure the bust length I from the vertebra (base of the neck) over the shoulder up to the bust point. Put the measuring tape in the shape of a normal neckline from the vertebra to the shoulder. To determine the position of the base of the neck (vertebra), put the measuring tape around the neck and measure from bust point to bust point. Note one-half of this measurement.

 

FL I I— Front length I II

This figure shows the measurement of the Front length

 

  • Measure the front waist length from the vertebra (base of the neck) over the shoulder and the bust point to the lower edge of the waist tape measure. Up to the bust it is the same measuring process as With the bust length I. The double measurement can be taken here as well. Compare the measured front waist length 11 (Front waist length I minus neck width = FWL II) with the calculated front waist length. More than 1 cm difference shows a figure problem (z. B. Full bust, round shoulders, low waist)‚ Which must be taken into account during the pattern development. Note: Back and front length are balance measurements. They must be in the tight proportion (e.g. BWL + 4 cm = FWL II etc. – see measurement chart).

 

BW — Back width

This figure shows the measurement of the Back width

 

  • Measure the back Width over the lower part of the shoulder blades from arm fold to arm fold. Note only half of the measurement. Compare the measured back Width With the calculated one. Use the calculated measurement in the case of a deviation up to 0.5 cm. For a  greater difference use the average value between the calculated and measured back Width.

 

NW – Neck width

This figure shows the measurement of the Neck width

  • Measure from the nape of the neck (7th cervical vertebra) horizontally to the shoulder seam. This measurement is half the width of the back neckline.

 

Sw – Scye width

This figure shows the measurement of the Scye width

 

  • Measure the scye width between the front and back armhole pitch line. The scye width determines the armhole width. The scye width can also be calculated.

 

Cw –  Chest width

 

This figure shows the measurement of the Chest width

  • Measure horizontally from the centre front to the beginning of the arm. The chest width can also be calculated.

 

TIP: Measuring is a difficult task that requires a lot of practice and experience. Errors and deficiencies are transferred to the cut and result in fitting errors in the garment. If you have recognized the faults of a figure well, you should also try to conceal them as far as possible by selecting the appropriate model or with the help of carefully considered seam layers. Afterwards it has to be said that the described measurements are sufficient to create a well fitting pattern in the bespoke tailoring atelier as well as in the industrial pattern department. However, there are cases where additional measurements are required. These include, for example, customers with extremely strong arms or unusual neck widths. Information for professional pattern construction and the construction of bespoke patterns for special figure types you can find in our book Metric Patternmaking for Dresses & Blouses.

PDF Download: Download M. Müller & Sohn - Book - Women - Metric Pattern Making - Dresses and Blouses
116,80 €
TOC

 

Bg – Biceps girth

This figure shows the measurement of the Biceps girth

  • Measure the biceps horizontally around the fullest part of the upper arm.

 

 

El – Elbow length

This figure shows the measurement of the Elbow length

 

  • Measure the elbow length over the hanging arm from the arm head to the elbow.

 

Sl –  Sleeve length

This figure shows the measurement of the Sleeve length

  • Measure the sleeve length over the hanging arm with slightly forward bend underarm from the arm head over the elbow to the wrist bone.

Shw – Shoulder width

This figure shows the measurement of the Shoulder width

 

  • Measure the shoulder from the beginning of the neck to the beginning of the arm at the shoulder.

 

Wrg – Wrist girth

This figure shows the measurement of the Wrist girth

 

  • Measure the wrist circumference horizontally over the wrist bone.

 

Ng – Neck girth

This figure shows the measurement of the Neck girth

 

  • Measure the circumference of the neck at the transition to the upper body.

 

 

 

BpBp – Bustpoint distance

This figure shows the measurement of the Bustpoint distance

 

  • Measure horizontally from the left to the right bust point.

 

Heg – Head girth

This figure shows the measurement of the Hip girth

 

  • Measure the horizontal circumference over the fullest part of the head.

Measuring for trousers and skirts

Overview of the measurements used for the pattern construction of trousers and skirts:

1. Wg – Waist grith:

  •  Measure the circumference at the narrowest part of the waist. > see above

2. Hg – Hip grith:

  •  Measure the hip circumference horizontally over the fullest part of the seat and/or the hip. > see abov

 

Note: For the following length measurements, apply a waist band (a measuring tape with hooks and eyelets).

3. Kl –Knee length:

  • Measure the knee length at the centre front vertically from the waist to the middle of the knee.

4. Fl – Front length:

  • Measure at the centre front from the lower edge of the waistband to the floor.

5. Rl – Rear length:

  • Measure at the centre back from the lower edge of the waistband to the floor.

6. Sl – Side length:

This figure shows the measurement of the Side length

 

  • Measure vertically along the side from the waist to the floor.

6a. Is – Inseam:

This figure shows the measurement of the Inseam

 

  • Measure vertically from the crotch to the floor. The inseam can also be calculated by subtracting the body rise measurement from the side length.

 

7. Br – Body rise:

This figure shows the measurement of the Body rise

 

  • Sit the client being measured on a hard chair or stool, and measure along the side from the lower edge of the waist measure tape vertically down wards to the seat of the chair.

7a. WCW – Waist-crotch-waist:

This figure shows the measurement of the Waist-crotch-waist measure

 

  •  Measure the crotch length from the front waist to the back waist. This measurement is only needed to verify the correct crotch length and is not needed for the pattern construction.

.

8. Tg – Thigh girth:

This figure shows the measurement of the Thigh girth

 

  • Measure the thigh circumference horizontally over the fullest part of the thigh.

9. Kbg – Kneeband girth:

This figure shows the measurement of the Kneeband girth

 

  • Measure the circumference at the narrowest part just below knee.

10. Cag – Calf girth

This figure shows the measurement of the Calf girth

 

  • Measure the circumference over the fullest part of the calf.

11. Ag  – Ankle girth:

This figure shows the measurement of the Ankle girth

 

  • Measure the circumference over the fullest part of the ankle.

 

PDF Download: Download Women Measurement Charts
82,00 €
TOC
  • If you don´t want to construct a bespoke pattern, you can work with the Measurement Chart for Women’s Wear.
Product: Zubehör Maßband 1,5 m
Zubehör Maßband 1,5 m
Measuring Tape 1,5 m

Leave a Reply

Your email address will not be published. Required fields are marked *